VBR BLADE

CAT grader blade part numbers and sizes

A CAT part number fixes the size, hole count and bolt size of a motor grader cutting edge. This chart lists 15 common numbers and shows which ones are easy to mix up.

Grader blades are usually ordered by part number, and the CAT number is the reference many parts books and sellers use. Each number stands for one combination of thickness, width, length, hole count and bolt size. If one of these is different, the blade will not sit on the moldboard the way it should.

The size chart

All dimensions in millimetres. Bolt size is the plow bolt diameter in inches.

Part number Thickness Width Length Holes Bolt
5D9553 16 152 1828 13 5/8″
5D9554 16 152 2133 15 5/8″
5D9562 16 203 1828 13 5/8″
5D9561 16 203 2133 15 5/8″
7D1158 16 203 2133 15 3/4″
5D9556 19 152 1828 13 5/8″
5D9557 19 152 2133 15 5/8″
5D9558 19 203 1828 13 5/8″
5D9559 19 203 2133 15 5/8″
7D1576 19 203 1828 13 3/4″
7D1577 19 203 2133 15 3/4″
4T2244 25 203 1828 13 5/8″
4T2231 25 203 1828 13 3/4″
4T2242 25 203 2133 15 5/8″
4T2233 25 203 2133 15 3/4″

The metric values are rounded from inch sizes: 16 mm is 5/8″, 19 mm is 3/4″, 25 mm is 1″; 152 mm is 6″ and 203 mm is 8″; 1828 mm is 6 ft (72″) and 2133 mm is 7 ft (84″). Cat lists 5D-9553, for example, as 0.626 × 6.0 × 71.906 in.

How the sizes line up

In this group of numbers, length and hole count go together: the 6 ft blades have 13 holes and the 7 ft blades have 15. On 5D-9553, Cat gives a hole spacing of 6.0 in and an end hole spacing of 3.0 in, with a square hole for a 5/8″ plow bolt. Two blades of the same length can still differ in thickness, width and bolt size, so check all five values, not only the length.

Thickness and width change how much steel the edge carries. Cat's motor grader brochure notes that an 8″ edge gives twice the wear material of a 6″ edge, and that a narrow, thin edge can be the better value for fine finish work. The thickness and width guide covers this choice.

Codes that are easy to mix up

Some pairs have exactly the same size and hole count. Only the bolt size is different:

Size (mm) Holes 5/8″ bolt 3/4″ bolt
16 × 203 × 2133 15 5D9561 7D1158
19 × 203 × 1828 13 5D9558 7D1576
19 × 203 × 2133 15 5D9559 7D1577
25 × 203 × 1828 13 4T2244 4T2231
25 × 203 × 2133 15 4T2242 4T2233

A 3/4″ plow bolt does not pass through a 5/8″ hole, and a 5/8″ bolt in a 3/4″ hole will not seat properly. Before you order, check which bolt your moldboard takes. Cat's brochure also mentions moldboard bushings that reduce 3/4″ holes to 5/8″ to standardise hardware, so the bolt size on a machine is not always the one it was first delivered with.

Which machines use them

The CAT parts page for each number lists the machines it is used on. For 5D-9553 the list includes motor graders such as the 120, 12G, 12H, 140, 140G and 140H. On each VBR part page we repeat the CAT motor grader list as given on the CAT parts page. These lists can be incomplete, and a machine that has been modified may carry a different moldboard, so the size check above still matters.

Numbers from other brands

Other suppliers often sell their blades under the same CAT number. Some use their own numbers; the John Deere DURA-MAX range, for example, has its own T-numbers for blades of the same size. A reference number tells you that a blade of that description exists. It does not prove that the hole pattern is the same. Our cross-reference shows each reference with its basis, for example "Same size and hole count; hole pattern not confirmed".

Before you ask for a quote

  1. Find the number in your parts book or on the invoice of the last order.
  2. If there is no number, measure the blade: see how to measure a grader blade.
  3. Choose the material: boron steel (30MnB5) or carbon steel.
  4. Note the quantity and whether you need plow bolts and nuts.

With those four points, a supplier can confirm the part and the stock in one reply.