VBR BLADE

Grader blade thickness and width: 16, 19 or 25 mm?

Thickness and width decide how much steel a cutting edge carries and how easily it cuts. Here is what changes between the common sizes, and how to tell when an edge is due.

Most motor grader cutting edges come in three thicknesses, 16, 19 and 25 mm (5/8″, 3/4″ and 1″), and two widths, 152 and 203 mm (6″ and 8″). The machine's moldboard sets the length and the hole pattern. Within that, thickness and width are a choice.

Width: how much steel there is to wear

The width of a new edge is the height of steel between the bolt line and the cutting edge. Only part of it can be used before the edge must come off. Cat's motor grader brochure states that an 8″ edge gives twice the wear material of a 6″ edge, and that the wider edge halves hardware cost and the downtime for removing and installing edges.

A 6″ edge still has its place. The same brochure notes that for finish tolerances under 1/4″ (6 mm), a narrow, thin edge may be the best value. Fine grading needs a clean, predictable edge more than a large wear reserve.

Thickness: penetration against strength

A thinner edge cuts into hard material more easily. Cat's brochure lists a thinner edge, a serrated edge or a bit system as the options when more penetration is needed. A thicker edge carries more steel through the section and stands up better to heavy work, but it needs more force to cut.

Thickness Typical use (general guidance)
16 mm (5/8″) Road maintenance, finish grading, lighter machines
19 mm (3/4″) General grading and maintenance
25 mm (1″) Heavy work, hard and abrasive ground

This table is a starting point, not a rule. The moldboard and the machine's parts book come first: some machines are listed for one thickness only. A thicker blade also needs longer plow bolts, because the bolt passes through the blade and the moldboard before the nut.

Example: one size, three thicknesses

The VBR list has three blades of 203 × 1828 mm with 13 holes for 5/8″ bolts: 5D9562 (16 mm), 5D9558 (19 mm) and 4T2244 (25 mm). All three fit the same moldboard with the same bolt pattern; the difference is thickness. If your moldboard and parts book allow these thicknesses, choose by the work. When the thickness changes, check the bolt length too.

Edge shape

Cat's brochure recommends a flat edge for road development or heavy maintenance, and a curved edge for reconditioning or finish grading, where it carries material forward and leaves a smooth surface. Serrated versions of both exist for hard-packed gravel, frozen earth or ice. Shape and thickness are chosen together.

When to inspect

An article in For Construction Pros (2008) reports that equipment makers recommend inspecting cutting edges visually every 25 to 50 hours, depending on the material. Wear depends on hours of use, the abrasiveness of the material and the operator. In very abrasive conditions an edge can wear out within a day.

Look for:

  • remaining width at the most worn point;
  • uneven wear along the length, often heavier at the ends;
  • worn or loose plow bolts;
  • cracks starting at bolt holes;
  • wear on the end bits (corner pieces).

When to replace

The same article quotes a figure from the field: an edge with about 1½″ of usable depth works well, and once about 1″ of it has worn away the edge should be changed. If it is not, the moldboard itself starts to wear. A worn moldboard can no longer hold a new edge properly and then has to be repaired or replaced, which costs far more than an edge.

Two habits help:

  1. Change edges in time. Mark the minimum width on the blade or in the service log, and change at that point.
  2. Change bolts with the edge. Bolts wear in the dirt as well; reusing them saves little.

Working practice

Cat's brochure adds a few operating notes: keep travel speed moderate, because excess speed can cause slivering of the edge; avoid changing the moldboard angle constantly; and start with the moldboard slightly ahead of the edge. These are Cat's recommendations for its machines; your machine's operator manual takes precedence.

Choosing a VBR blade

The VBR list covers 16, 19 and 25 mm, 152 and 203 mm, in 1828 and 2133 mm lengths. Use the grader blade table to filter, or read the part number chart to compare sizes side by side.