Plow bolts, nuts and grader blade replacement
A cutting edge is only as secure as its bolts. What a plow bolt is, how to pick the size, and what to check when you change a blade.
What a plow bolt is
A plow bolt has a countersunk flat head and a square neck under the head. Fastener suppliers describe the common type used on cutting edges as the "No. 3 head" plow bolt. The square neck fits the square countersunk hole in the cutting edge, a hole shape described in the SAE J740 standard. Two things follow:
- the bolt cannot turn while the nut is tightened from behind the moldboard;
- the head sits flush with the face of the blade, so it does not catch material.
The nut is a standard hex nut on the back of the moldboard.
Bolt size: 5/8″ or 3/4″
The bolt size is set by the blade and the moldboard holes. Most motor grader cutting edges in the common CAT sizes take 5/8″ or 3/4″ plow bolts. Cat lists an 18 mm square hole for the 5/8″ bolt on 5D-9553.
Watch the pairs of part numbers that are identical except for the bolt size, for example 5D9561 (5/8″) and 7D1158 (3/4″). Cat's brochure also mentions moldboard bushings that reduce 3/4″ holes to 5/8″, so check the moldboard as it is now, not only the parts book.
Length
Plow bolt length is measured from the top of the head to the end of the bolt. The bolt must pass through the blade and the moldboard and leave enough thread for the full nut. A thicker blade, or a blade with an overlay, needs a longer bolt. If you are unsure, measure an old bolt that held a blade of the same thickness.
Grade
Plow bolts come in different strength grades. The Aspen Fasteners specification sheet describes Grade 5 (medium-carbon steel, quenched and tempered, minimum tensile strength 120,000 psi), noting its use on road graders, and Grade 8 (alloy steel, minimum 150,000 psi). Cat's brochure says it matches Grade 8 hardware to its own ground engaging tools. Use the grade your machine's manual specifies.
Replacing a cutting edge: checklist
General guidance only. Follow the machine's service manual and safety instructions.
- Park safely. Level ground, moldboard lowered and supported, engine off, controls secured.
- Remove the old bolts. On a worn edge the bolts may be rounded or rusted. Cat notes that its threads sit in the back half of the edge hole so worn edges can still be removed.
- Inspect the moldboard. Look for wear on the lower edge, elongated holes and cracks. A worn moldboard will not hold a new edge flat.
- Clean the seat. Remove dirt and rust from the contact surface so the new edge sits fully against the moldboard.
- Check the new blade. Compare part number, length, hole count and bolt size with the old one before you lift it.
- Fit new bolts and nuts. Bolts wear in the dirt together with the edge; a 2008 field article recommends replacing them with every edge.
- Tighten evenly. Work from the centre outwards to the torque given in the machine manual.
- Check again after the first hours of work. Re-tighten if the manual calls for it.
What to keep in stock
If blades are changed in the field, keeping one set of bolts and nuts with each spare blade saves time: 13 sets for a 6 ft blade with 13 holes, 15 for a 7 ft blade with 15 holes, plus a few spare nuts. Store bolts dry and covered; rusty threads change the tightening torque.
End bits and turning edges
End bits (the corner pieces at each end of the moldboard) usually wear faster than the centre edges and should be checked at the same time. Cat's brochure mentions overlay end bits that can be rotated for a second wear life. Some machines use reversible edges that can be turned over when one side has worn; whether a given blade can be turned depends on its cross-section.
Ordering bolts with the blades
VBR supplies plow bolts and nuts with its grader blades. Tell us the bolt size, the quantity (one bolt and one nut per hole) and the blade part numbers they are for, and we quote them together. See plow bolts and nuts.